Parallel (PC)

25 PIN D-SUB FEMALE (At the PC)

25 PIN D-SUB FEMALE at the PC.

Контакт Сигнал Dir Описание
1 /STROBE --> Strobe
2 D0 --> Data Bit 0
3 D1 --> Data Bit 1
4 D2 --> Data Bit 2
5 D3 --> Data Bit 3
6 D4 --> Data Bit 4
7 D5 --> Data Bit 5
8 D6 --> Data Bit 6
9 D7 --> Data Bit 7
10 /ACK <-- Acknowledge
11 BUSY <-- Busy
12 PE <-- Paper End
13 SEL <-- Select
14 /AUTOFD --> Autofeed
15 /ERROR <-- Error
16 /INIT --> Initialize
17 /SELIN --> Select In
18 GND --- Signal Ground
19 GND --- Signal Ground
20 GND --- Signal Ground
21 GND --- Signal Ground
22 GND --- Signal Ground
23 GND --- Signal Ground
24 GND --- Signal Ground
25 GND --- Signal Ground
Примечание: Direction is Computer relative Device.
Опубликовал: Joakim Ogren, Petr Krc
Источник: ?
Все комментарии присылайте Joakim Ogren.

Parallel (Amiga)

25 PIN D-SUB FEMALE (At the Amiga)

25 PIN D-SUB FEMALE at the Amiga.

Контакт Сигнал Dir Описание
1 /STROBE --> Strobe
2 D0 <-> Data Bit 0
3 D1 <-> Data Bit 1
4 D2 <-> Data Bit 2
5 D3 <-> Data Bit 3
6 D4 <-> Data Bit 4
7 D5 <-> Data Bit 5
8 D6 <-> Data Bit 6
9 D7 <-> Data Bit 7
10 /ACK <-- Acknowledge
11 BUSY <-> Busy
12 POUT <-> Paper Out
13 SEL <-> Select (Shared with RS232 RING-indicator)
14 +5V PULLUP --> +5 Volts DC (10 mA max)
15 n/c - Not connected.
16 /RESET --> Reset
17 GND --- Signal Ground
18 GND --- Signal Ground
19 GND --- Signal Ground
20 GND --- Signal Ground
21 GND --- Signal Ground
22 GND --- Signal Ground
23 GND --- Signal Ground
24 GND --- Signal Ground
25 GND --- Signal Ground
Примечание: Direction is Computer relative Peripheral.
Опубликовал: Joakim Ogren
Источник: Amiga 4000 User's Guide from Commodore
Все комментарии присылайте Joakim Ogren.

Parallel (Amiga 1000)

25 PIN D-SUB MALE (At the Amiga 1000)

25 PIN D-SUB MALE at the Amiga 1000.

Контакт Сигнал Dir Описание
1 /STROBE --> Strobe
2 D0 <-> Data Bit 0
3 D1 <-> Data Bit 1
4 D2 <-> Data Bit 2
5 D3 <-> Data Bit 3
6 D4 <-> Data Bit 4
7 D5 <-> Data Bit 5
8 D6 <-> Data Bit 6
9 D7 <-> Data Bit 7
10 /ACK <-- Acknowledge
11 BUSY <-> Busy
12 POUT <-> Paper Out
13 SEL <-> Select (Shared with RS232 RING-indicator)
14 GND --- Signal Ground
15 GND --- Signal Ground
16 GND --- Signal Ground
17 GND --- Signal Ground
18 GND --- Signal Ground
19 GND --- Signal Ground
20 GND --- Signal Ground
21 GND --- Signal Ground
22 GND --- Signal Ground
23 +5V --> +5 Volts DC (10 mA max)
24 n/c - Not connected.
25 /RESET --> Reset
Примечание: Direction is Computer relative Peripheral.
Опубликовал: Joakim Ogren
Источник: Amiga 4000 User's Guide from Commodore
Все комментарии присылайте Joakim Ogren.

ECP Parallel

ECP = Extended Capabilities Port

25 PIN D-SUB FEMALE (At the PC)

25 PIN D-SUB FEMALE at the PC.

Контакт Сигнал Dir Описание
1 nStrobe --> Strobe
2 data0 <-> Address, Data or RLE Data Bit 0
3 data1 <-> Address, Data or RLE Data Bit 1
4 data2 <-> Address, Data or RLE Data Bit 2
5 data3 <-> Address, Data or RLE Data Bit 3
6 data4 <-> Address, Data or RLE Data Bit 4
7 data5 <-> Address, Data or RLE Data Bit 5
8 data6 <-> Address, Data or RLE Data Bit 6
9 data7 <-> Address, Data or RLE Data Bit 7
10 /nAck <-- Acknowledge
11 Busy <-- Busy
12 PError <-- Paper End
13 Select <-- Select
14 /nAutoFd --> Autofeed
15 /nFault <-- Error
16 /nInit --> Initialize
17 /nSelectIn --> Select In
18 GND --- Signal Ground
19 GND --- Signal Ground
20 GND --- Signal Ground
21 GND --- Signal Ground
22 GND --- Signal Ground
23 GND --- Signal Ground
24 GND --- Signal Ground
25 GND --- Signal Ground
Примечание: Direction is Computer relative Device.
Опубликовал: Joakim Ogren, Marco Furter
Источник: Microsoft MSDN Library: Extended Capabilities Port Specs
Info: Microsoft MSDN Library
Все комментарии присылайте Joakim Ogren.

ECP Parallel (Technical)

This file is designed to give a basic overview of the port found in most newer PC computers called ECP Parallel port.

This file is not intended to be a thorough coverage of the standard. It is for informational purposes only, and is intended to give designers and hobbyists sufficient information to design their own ECP compatible devices.

Signal Descriptions:

nStrobe

This signal is registers data or address into the slave on the assering edge during .

data 0-7

Contains address, data or RLE data. Can be used in both directions.

nAck

Valid data driven by the peripheral when asserted. This signal handshakes with nAutoFd in reverse.

Busy

This signal deasserts to indicate thна устройстве can accept data. In forward direction this handshakes with nStrobe. In the reverse direction this signal indicates that the data is RLE compressed by being low.

PError

Used to acknowledge a change in the direction of transfer. High=Forward.

Select

Printer is online.

nAutoFd

Requests a byte of data from the peripheral when asserted, handshaking with nAck in the reverse direction. In the forward direction this signal indicates whether the data lines contain ECP address or data.

nFault

Generates an error interrupt when asserted.

nInit

Sets the transfer direction. High=Reverse, Low=Forward.

nSelectIn

Low in ECP mode.

Опубликовал: Joakim Ogren , Rob Gill
Источник: Microsoft MSDN Library: Extended Capabilities Port Specs
Info: Microsoft MSDN Library
Все комментарии присылайте Joakim Ogren.

Centronics

36 PIN CENTRONICS FEMALE (At the Printer)

36 PIN CENTRONICS FEMALE at the Printer.

Контакт Сигнал Dir Описание
1 /STROBE <-- Strobe
2 D0 <-> Data Bit 0
3 D1 <-> Data Bit 1
4 D2 <-> Data Bit 2
5 D3 <-> Data Bit 3
6 D4 <-> Data Bit 4
7 D5 <-> Data Bit 5
8 D6 <-> Data Bit 6
9 D7 <-> Data Bit 7
10 /ACK --> Acknowledge
11 BUSY --> Busy
12 POUT --> Paper Out
13 SEL --> Select
14 /AUTOFEED <-- Autofeed
15 n/c - Not used
16 0 V --- Logic Ground
17 CHASSIS GND --- Shield Ground
18 +5 V PULLUP --> +5 V DC (50 mA max)
19 GND --- Signal Ground (Strobe Ground)
20 GND --- Signal Ground (Data 0 Ground)
21 GND --- Signal Ground (Data 1 Ground)
22 GND --- Signal Ground (Data 2 Ground)
23 GND --- Signal Ground (Data 3 Ground)
24 GND --- Signal Ground (Data 4 Ground)
25 GND --- Signal Ground (Data 5 Ground)
26 GND --- Signal Ground (Data 6 Ground)
27 GND --- Signal Ground (Data 7 Ground)
28 GND --- Signal Ground (Acknowledge Ground)
29 GND --- Signal Ground (Busy Ground)
30 /GNDRESET --- Reset Ground
31 /RESET <-- Reset
32 /FAULT --> Fault (Low when offline)
33 0 V --- Signal Ground
34 n/c - Not used
35 +5 V --> +5 V DC
36 /SLCT IN <-- Select In (Taking low or high sets printer on line or off line respectively)
Примечание: Direction is Printer relative Computer.
Опубликовал: Joakim Ogren, Peter Korsgaard, Petr Krc
Источник: ?
Все комментарии присылайте Joakim Ogren.

MSX Parallel

UNKNOWN (в компьютере)

14 PIN CENTRONICS FEMALE в компьютере.

Контакт Сигнал Dir Описание
1 /STB --> Strobe
2 PDB0 --> Data 0
3 PDB1 --> Data 1
4 PDB2 --> Data 2
5 PDB3 --> Data 3
6 PDB4 --> Data 4
7 PDB5 --> Data 5
8 PDB6 --> Data 6
9 PDB7 --> Data 7
10 n/c -  
11 BUSY <-- Printer is busy
12 n/c -  
13 n/c -  
14 GND - Signal Ground
Примечание: Direction is Computer relative Printer.
Опубликовал: Joakim Ogren
Источник: Mayer's SV738 X'press I/O map
Все комментарии присылайте Joakim Ogren.

Parallel (Olivetti M10)

Available on an old portable computer called Olivetti M10.

26 PIN IDC MALE (в компьютере)

26 PIN IDC MALE в компьютере.

Контакт Сигнал Dir Описание
1 /STROBE --> Strobe
2 D0 --> Data Bit 0
3 D1 --> Data Bit 1
4 D2 --> Data Bit 2
5 D3 --> Data Bit 3
6 D4 --> Data Bit 4
7 D5 --> Data Bit 5
8 D6 --> Data Bit 6
9 D7 --> Data Bit 7
10 /ACK <-- Acknowledge
11 BUSY <-- Busy
12 PE <-- Paper End
13 SELIN <-- Select In
14 GND --- Signal Ground
15 GND --- Signal Ground
16 GND --- Signal Ground
17 GND --- Signal Ground
18 GND --- Signal Ground
19 GND --- Signal Ground
20 GND --- Signal Ground
21 GND --- Signal Ground
22 GND --- Signal Ground
23 GND --- Signal Ground
24 GND --- Signal Ground
25 RESETGND --- Reset Ground
26 /RESET <-- Reset
Примечание: Direction is Computer relative Device.
Опубликовал: Joakim Ogren, Filippo Fiani
Источник: ?
Все комментарии присылайте Joakim Ogren.

Amstrad CPC6128 Printer Port

34 PIN FEMALE EDGE (At the computer)

34 PIN FEMALE EDGE в компьютере.

Контакт Сигнал Описание
1 /STROBE Strobe
2 D0 Data 0
3 D1 Data 1
4 D2 Data 2
5 D3 Data 3
6 D4 Data 4
7 D5 Data 5
8 D6 Data 6
9 GND Ground
10 n/c Not connected
11 BUSY Busy
12 n/c Not connected
13 n/c Not connected
14 GND Ground
15 n/c Not connected
16 n/c Not connected
17 n/c Not connected
16 GND Ground
17 n/c Not connected
19 GND Ground
20 GND Ground
21 GND Ground
22 GND Ground
23 GND Ground
24 GND Ground
25 GND Ground
26 GND Ground
27 n/c Not connected
28 GND Ground
29 n/c Not connected
30 n/c Not connected
31 n/c Not connected
32 n/c Not connected
33 GND Ground
34 n/c Not connected
35 n/c Not connected
Примечание: Pin 18 does not exist
Опубликовал: Joakim Ogren, Agnello Guarracino
Источник: Amstrad CPC6128 User Instructions Manual
Все комментарии присылайте Joakim Ogren.

    

Поддержите сайт, поставте на нас ссылку.

Пример ссылкиКод ссылки
Схемы по радиосвязи
Схемы по радиосвязи
Выбрать другой баннер...

 
Сайт создан в системе uCoz
Сайт создан в системе uCoz